----------------------------------------------------------------------------- Stable (11h Prime64 under XP64) RMClock "Maximum Performance" CPU: Q6600, VID=1.2250V @3.504 GHz @1.344V Multi: 8 FSB: 438 MHz RAM: 2 x 2 GB OCZ PC2 8500 C5 Reaper @547.6MHz / DDR2 1098 (266/667, 4:5) RMClock settings: 0: FID 6 -> 2.629 GHz, VID 1.112 -> 1.248V cpuz 1: FID 7 -> 3.067 GHz, VID 1.162 -> 1.312V cpuz 2: FID 8 -> 3.504 GHz, VID 1.200 -> 1.344V cpuz used for "Maximum Performance" 3: FID 9, VID 1.225 -> 1.375V cpuz unused ----------------------------------------------------------------------------- Genie Bios settings: ----------------------------------------------------------------------------- Main Genie BIOS Page Exit Setup Shutdown.......................Mode 2 O. C. Fail Retry Counter..................0 CLOCK VC0 Divider.........................Auto CPU Clock Ratio...........................8x Target CPU Clock.........................3504 MHz CPU Clock.................................438 MHz Boot Up Clock.............................Auto DRAM Speed................................266/667 Target DRAM Speed........................DDR2 1098 PCIE Clock................................100 MHz PCIE Slot Config..........................1X 1X CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled SATA Spread Spectrum......................Disabled CPU Feature Page Thermal Management Control................Enabled PPM (EIST) Mode...........................Disabled Limit CPUID MaxVal........................Disabled CIE Function..............................Disabled Execute Disable Bit.......................Enabled Virtualization Technology.................Enabled Core Multi-Processing.....................Enabled DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Auto Clock Setting Fine Delay..................Listed Below CAS Latency Time (tCL)....................Auto RAS# to CAS# Delay (tRCD).................Auto RAS# Precharge (tRP)......................Auto Precharge Delay (tRAS)....................Auto All Precharge to Act......................Auto REF to ACT Delay (tRFC)...................Auto Performance Level.........................auto Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................Auto Write to PRE Delay (tWR)..................Auto Rank Write to Read (tWTR).................Auto ACT to ACT Delay (tRRD)...................Auto Read to Write Delay (tRDWR)...............Auto Ranks Write to Write (tWRWR)..............Auto Ranks Read to Read (tRDRD)................Auto Ranks Write to Read (tWRRD)...............Auto Read CAS# Precharge (tRTP)................Auto ALL PRE to Refresh........................Auto Clock Setting Fine Delay Page Ch1 Clock Crossing Setting................Aggressive DIMM 1 Clock fine delay...................Auto DIMM 2 Clock fine delay...................Auto DIMM 1 Control fine delay.................Auto DIMM 2 Control fine delay.................Auto Ch 1 Command fine delay...................Auto Ch2 Clock Crossing Setting................Aggressive DIMM 3 Clock fine delay...................Auto DIMM 4 Clock fine delay...................Auto DIMM 3 Control fine delay.................Auto DIMM 4 Control fine delay.................Auto Ch 2 Command fine delay...................Auto Ch1Ch2 CommonClock Setting................Aggressive Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Auto Channel 1 Phase 1 Pull-In.................Auto Channel 1 Phase 2 Pull-In.................Auto Channel 1 Phase 3 Pull-In.................Auto Channel 1 Phase 4 Pull-In.................Auto Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto Voltage Setting Page CPU VID Control...........................Auto 1.2200V CPU VID Special Add.......................110.86% DRAM Voltage Control......................2.120V SB Core/CPU PLL Voltage...................1.510V NB Core Voltage...........................1.467V CPU VTT Voltage...........................1.283V VCore Droop Control.......................Disabled Clockgen Voltage Control..................3.45V GTL+ Buffers Strength.....................Strong Host Slew Rate............................Weak GTL REF Voltage Control...................Enable CPU GTL 1/3 REF Volt......................88 CPU GTL 0/2 REF Volt......................88 North Bridge GTL REF Volt ................88